SORENSEN DHP-30-330

0 - 30 VDC  0 - 330 AMPS

$1695

Available in our eBay Store

OR

SOLD

This supply is basically new, it was used once for a short time and then de-installed

so we are listing it as used.

The DHP family provides models ranging in output power from 5 kW to 20 kW in a single chassis. Programmable output voltages range from 5V to 400 VDC, delivering up to 3,000 amperes. This family has two operational modes, constant-voltage and constant-current.

The DHP family uses control technology that allows 9 auto sequence steps, each step can be up to 99,999 seconds in duration. Combining all the steps allows a maximum auto-step program 27.7 hours long. Various voltages, currents and durations can be programmed for each step.

This family has standard analog and a variety of combinations of IEEE-488.2, RS 232 and/or isolated analog input control interface options.

All models come with the standard Sorensen 5-year warranty and CE Mark

This equipment will ship freight secured to a pallet. We will protect it with heavy covering.

[Click on Photos for Larger Image]

Specifications

Common Operating Temperature 0°C to +50°C, no derating Storage Temperature -20°C to 70°C Cooling Internal fan Front Panel Controls Keypad to select/adjust voltage, current and power with non-volatile memories to store commonly used parameters Displays and Indicators Back lit LCD alphanumeric display and LEDs Built-in Protection Overtemperature, brown out, turn on surge limit, slow start, overvoltage (OVP resettable without recycling power) Remote Sense The maximum line drop is 3% per line or 1V for 5-15V units, 3V for all others. Line drop subtracts from the maximum available output voltage at full rated power. Remote Control/Monitor (Rear Panel) On/off control via contact closure, 6-120 VDC, 12-240 VAC, TTL or CMOS switch, output voltage and current monitor, (0-10 volt) OVP limit set, summary fault status Internal Programming 9 memories are on-board for auto-step programming. Each step can be 1 second to 99,999 seconds or 27.78 hours long.

Input Voltage and Frequency 190-253 VAC, 47-63 Hz (Standard) 360-440 VAC, 47-63 Hz (Option) 432-528 VAC, 47-63 Hz (Option) Three phase, 3-wire plus ground, Delta or Wye input may be used (Wye does not require the neutral connection) Power Factor 0.72 min.

Output Voltage, Current, and Ripple 0-30 vdc 0-330  amps 10 mV ripple Regulation (Line or Load ) Voltage: 0.1% of maximum rated output Current: 0.5% of maximum rated output Line: For input voltage variation over the AC input voltage range, with constant rated load. Load: For 0-100% load variation, with constant nominal line voltage. Transient Response 2 ms to steady state output voltage (within 2% of Vmax) for 30% step load change Stability ±0.05% maximum rating per 8 hours after a 30 minute warm-up time at fixed line, load and temperature Efficiency 80% minimum at full load Temperature Coefficient 0.02%/°C of rated output voltage; 0.03%/°C of rated output current. Change in output per °C change in ambient temperature, with constant line and load.

Remote Digital Control Programming Resolution Voltage: 0.3% of full scale; Current: 0.3% of full scale; Overvoltage Protection: 0.5% of full scale (full scale is 110% of maximum output voltage) Programming Accuracy Voltage: 0.1% + 0.3% of maximum output voltage; Current: 0.3% + 0.3% of maximum output current*; Overvoltage Protection: 0.5% + 0.5% of maximum output voltage Readback Resolution Voltage and Current: 0.3% of full scale Readback Accuracy Voltage: 0.1% + 0.3% of full scale output voltage; Current: 0.3% + 0.3% of full scale output current* Soft Calibration Calibration via front panel without removing chassis covers Software LabVIEW® driver for M9D Regulatory Compliance CE mark, UL(Up to 10kW output), cUL (Up to 10kW output)

Dimensions Case 1 3U - 5-1/4” (133 mm) H 19” (482 mm) W 22” (558 mm) D

Weight & Shipping Weight Weight: Maximum Case I: 80 lbs. (55 kg) Shipping Weight: Maximum Case I:120 lbs. (73 kg)